MT115
MT115MT115
MT115-
--
-111/
111/111/
111/DTP Receiver to Computer/Component AV
DTP Receiver to Computer/Component AVDTP Receiver to Computer/Component AV
DTP Receiver to Computer/Component AV
User’s Guide
400-0443-005
1
Welcome!
We greatly appreciate your purchase of the MT115-111 Dual Twisted Pair
Receiver to Computer/Component Video + Audio. We are sure you will find
it reliable and simple to use. Superior performance for the right price, backed
by solid technical and customer support is what ALTINEX has to offer.
We are committed to providing our customers with
Signal Management Solutions
®
to the most demanding audiovisual
installations at very competitive pricing and we welcome you to join the
ranks of our many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your MT115-111 and keep it
handy for future reference. These safety instructions are to ensure the long
life of your MT115-111 and to prevent fire and shock hazards. Please read
them carefully and heed all warnings.
1.1 General
• Qualified ALTINEX service personnel or its authorized representatives
must perform all service.
1.2 Handling
• Handle the MT115-111 carefully. Dropping or jarring can damage the
card.
• The MT115-111 contains components that are sensitive to electrostatic
discharge (ESD). Always use ESD safety precautions when touching the
card.
• To prevent fire or shock, do not expose this unit to water or moisture.
Do not place the MT115-111 in direct sunlight, near heaters or heat-
radiating appliances, or near any liquid. Exposure to direct sunlight,
smoke, or steam can harm internal components.
• Do not pull any cables that are attached to the MT115-111.
1.3 Cleaning
• Clean only the connector area with a dry cloth. Never use strong
detergents or solvents such as alcohol or thinner. Do not use a wet cloth
or water to clean the card. Do not clean or touch any component or
PCB.
1.4 FCC Notice
• This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
• This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions found herein, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
• Any changes or modifications to the unit not expressly approved by
ALTINEX, Inc. could void the user’s authority to operate the
equipment.
2. Installation Procedures
Step 1. Determine the appropriate switch settings using Diagram 3 on page 6.
Step 2. Turn off power to the MultiTasker system and disconnect from AC power.
Step 3. Remove an unused slot cover (MT200-101). Identify the slot number and note that it is for RS-232 control.
Step 4. Slide the MT115-111 into the enclosure in order to connect it to the bus. Make sure that the card fits into place and secure the card by tightening its
retainer screws.
Step 5. Restore power to the MultiTasker enclosure. The LEDs for each input should be on and red.
Step 6. Connect the computer/component video and audio devices to Outputs 1 and 2.
Step 7. Connect the 4TP IN1 to the output of its Twisted Pair transmitter. If a properly formatted input signal is available, the input LED will turn green.
Step 8. Connect the 4TP IN2 to the output of its Twisted Pair transmitter. If a properly formatted input signal is available, the input LED will turn green.
Step 9. The MT115-111 is ready for operation.
Step 10. Video equalization is provided to fine tune the displayed image on the remote display. The equalization adjustments on the MT115-111 and Twisted
Pair transmitter work together. Adjust equalization by setting both the transmitter and receiver to minimum. Then slowly increase the equalization
on the receiver until an image is present. Then adjust the equalization on both units for the best image.
Step 11. The MT115-111 also has video gain adjustment capability through RS-232 control.
3. Limited Warranty/Return policies
Please see the ALTINEX website at www.altinex.com for details on warranty and return policies.
Kommentare zu diesen Handbüchern